Almost nobody wires LED strip in series. What a job calls “series” is end-to-end chaining, which stays parallel electrically; the trouble is the current every run pulls through the first joint. Feed each run in parallel instead, from the driver or a tap, within the length its spec table allows per feed.
“Series” on a Strip Job Means End to End
Inside a 24V strip, every cut section is already wired in parallel across two copper rails. Joining two reels end to end only makes the rails longer, so every section still sees the same nominal 24V. That is the layout people mean by “series” when they say they wired strip in series: one run plugged into the end of the last.
True series is something else. Two 12V strips wired in series on a 24V supply share the voltage in proportion to their load. If the two have different lengths or wattages, the smaller load takes more than 12V and runs hot while the other runs dim, and a cut or failed section changes the split again. A rough picture, treating each strip as a fixed load: a 10 W strip and a 20 W strip, both 12V, in series on 24V. The 10 W strip has twice the resistance of the 20 W strip, so it takes about 16V and the 20 W strip about 8V. One is overdriven by a third, the other barely lights. Real LEDs are not fixed resistors, and their steep voltage curve makes the split less predictable, not better. No strip on a commercial job is designed to be wired that way. The rest of this page is about the layout that does happen, end to end, and the two parallel layouts that replace it.
Why End to End Fails: Current Through the First Joint
Take four 15 ft runs of COB strip, UT-C480-8 run at 24V, 3.2 W/ft. Each run loads 48 W, which is 2.0 A at 24V. Chained end to end, they become one 60 ft run that loads 192 W, and all 8.0 A passes through the first connector and the first few inches of strip copper.
Two limits are broken at once:
- The joint. Our strip-to-strip and wire-to-strip connectors are rated 5 A. The first joint in the chain carries 8 A, the second 6 A, the third 4 A. A joint over its rating runs hot, and a hot joint gains resistance and gets hotter, the cycle our guide to LED strip connectors overheating traces.
- The run limit. UT-C480-8 lists 16 ft (5 m) per feed. A 60 ft run fed from one end is almost four times that, so the far end sits well below 24V and looks dimmer than the start. The mechanism is in our guide to why the far end of a strip goes dim.
The chain also hides a third problem: with all four runs on one feed, the driver has to be at least a 240 W supply, so the layout can no longer be Class 2. A run that stays within its rated length per feed, fed in parallel, avoids all three.
Parallel Layout 1: Home Runs
In a home-run layout, every run gets its own two-conductor cable back to the driver location. The driver output lands on a terminal block, or each run has its own driver, and no current for one run passes through another run’s joints.
Home runs are the default for Class 2 work. Our 24V Class 2 drivers are rated 60 W or less, and a 15 ft run of UT-C480-8 is the most one 60 W driver carries at 80% of its rating, as our power supply sizing guide works out. So four runs become four drivers, four outputs and four Class 2 circuits. Do not tie two Class 2 outputs together to feed one run unless the data sheet allows it, as the no paralleled outputs section of our Class 2 guide explains.
The cost of home runs is cable. The far run needs the longest cable and sets its gauge; the near runs could use a smaller gauge, but one gauge for all of them is easier to order, pull and check.
Runs of different lengths fit this layout well, because each one is sized on its own. A 9 ft return at the end of a cove loads 28.8 W of UT-C480-8, which a 40 W Class 2 driver such as UT-D40-24-C2 carries at 72%, while the full 15 ft runs stay on 60 W drivers. A single run longer than the strip’s limit per feed is a different case: it is fed at both ends or at intervals, every feed from the same driver, which our voltage drop guide covers under feed points.
Parallel Layout 2: Trunk and Taps
A trunk layout uses one heavier cable from the driver along the runs, with a tap at each run’s feed point. Each tap feeds one run within its rated length, and the splices sit in boxes as the wiring method for that circuit requires, confirmed with the AHJ. The strip side looks the same as with home runs; the difference is the cable before it.
The trunk carries the sum. Between the driver and the first tap it carries every run’s current, then a little less after each tap, so the trunk’s drop adds up segment by segment. A trunk also usually means one large driver: on the four-run cove that is 192 W of load, which at 80% needs at least a 240 W driver, such as the 250 W UT-D250-1224-20S. That driver is not Class 2, so its output is wired as a power circuit, with the wiring method and any overcurrent protection on the taps confirmed against the driver’s data sheet and with the AHJ.
The trunk is where a shared cable goes wrong. Our voltage drop guide warns against one cable for several feeds, because an undersized shared cable becomes the bottleneck and the hottest conductor in the ceiling, and our wiring diagrams give each run its own pair. A trunk is only acceptable when it is sized for the sum of every run behind it, as the worked example below does. Home runs stay our default; a trunk suits a long run of identical sections with a cable path along them and no Class 2 requirement.

Making the Parallel Joints
A parallel layout has more joints than a chain, so each one has to be made the same way every time. Three places matter:
- At the driver. A driver has one output pair, or a few. Land the home runs on a terminal block rated for the total current, one pair per run, rather than twisting several cables under one screw. Label each pair with the run it feeds.
- At the tap. On a trunk, each tap is a splice in a box. Keep the box reachable after the ceiling or millwork closes, because a tap is where a fault is traced later, and confirm the box and access rules for the circuit with the AHJ.
- At the strip. The feed cable meets the strip through a wire-to-strip connector or a soldered lead. Our connectors are rated 5 A, and a 15 ft run of UT-C480-8 draws 2.0 A, so the connector has room. Match the conductor count, the PCB width and the IP rating to the strip, and keep plus and minus in the same order on every run.
Label both ends of every home run with the run number and the driver it comes from. On a job with twenty runs, the label is what lets someone find the right driver without unpowering the whole room.
Worked Example: A 60 ft Cove Fed Two Ways
The same four 15 ft runs, fed from a driver closet at one end of a 60 ft corridor cove. The feeds sit 5, 20, 35 and 50 ft from the closet, one way. Cable drop is the current times the resistance of both conductors, using the solid-copper values at 68°F from our feed wire voltage drop calculator:
| Layout | Driver(s) | Cable | Drop at the far run (50 ft) | Share of 24V |
|---|---|---|---|---|
| Home runs | 4 × 60 W Class 2 | 16 AWG, 2.0 A | 0.80 V | 3.3% |
| Home runs | 4 × 60 W Class 2 | 14 AWG, 2.0 A | 0.51 V | 2.1% |
| Trunk and taps | 1 × 250 W, non-Class 2 | 14 AWG trunk, 8 A to 2 A | 1.11 V | 4.6% |
| Trunk and taps | 1 × 250 W, non-Class 2 | 12 AWG trunk | 0.70 V | 2.9% |
| Trunk and taps | 1 × 250 W, non-Class 2 | 10 AWG trunk | 0.44 V | 1.8% |
No code sets a drop figure for low-voltage DC lighting cable. Common practice, as our calculator puts it, is to keep the cable under about 3% and the whole path, cable plus strip, under about 5%, because the eye notices the far end before the numbers look large. On that basis:
- Home runs pass at 14 AWG on every run. The near runs at 5 and 20 ft would pass at 18 AWG, but four cables of one gauge are simpler to order and pull.
- The trunk needs 12 AWG to land under 3% at the far tap; 14 AWG fails because every trunk segment carries the current of all the runs beyond it, 8, 6, 4 and then 2 A.
The cable count is easy to put side by side. The home runs need 5 + 20 + 35 + 50 = 110 ft of two-conductor 14 AWG cable and four drivers. The trunk needs 50 ft of 12 AWG, four short tap leads, four junction boxes and one driver.
So the trunk saves three drivers and about half the cable footage, and costs a heavier cable, a non-Class 2 output and taps in boxes. The home runs keep every circuit Class 2 and every run independent, which also means one failed run or driver leaves the other three lit.
Several Drivers on One Job
Most jobs with more than a few runs end up with several drivers, each feeding its own group. Three rules keep the groups clean:
- One run, one driver. A run fed at more than one point gets every feed from the same supply, as our voltage drop guide puts it. Where two drivers’ groups meet along a cove, the strip is cut between them, so no copper connects two outputs.
- Polarity at every feed. A reversed feed on a strip already powered from another point puts plus straight onto minus through the strip copper, a short across the driver that can trip it or destroy the strip. Check plus and minus at each feed before the strip is joined.
- Control follows power. On a dimmed or color job, every driver in a zone takes the same control signal. For RGB and tunable runs, a signal amplifier such as UT-CAMP-4 repeats the controller’s channels to the next group, with the channel order kept identical; our LED strip wiring diagrams show the conductor count per strip type.
Our drivers, controllers and connectors page lists the Class 2 drivers, the larger supplies and the connectors with their ratings.
Final Checks
- Every run is within the length its spec table lists per feed, and no run is chained from the end of another.
- No connector carries more current than its rating; add up the runs behind each joint.
- The far run’s cable drop is under about 3%, worked out at the real one-way distance.
- Each Class 2 run is on its own output; a trunk on a larger driver is wired as the power circuit it is.
- Where two drivers’ groups meet, the strip is cut, and polarity is checked at every feed before power-up.